| 263 files in 18 albums with 0 comments viewed 14211 times |
|
|
|
|
|
|
|
|
|
| 18 albums on 2 page(s) |
 |
|
2 |
|
| Random files |
22 views
|
|
Step 7: Pull the circuit board from it's housing267 viewsOnce you have separated the circuit board from the housing, gently pull it up and out. I recommend pulling out the 40 amp fuse at this point too. You may want to clean up the contacts of the fuse, I found mine to be slightly dirty. Take a screw driver or wire brush and lightly scrap away any dirt or corrosion to make the fuse conntacts shiny. Now look in the upper left hand corner of of the circuit board and follow step 8.
|
|
35 viewsHere I am driving the Viper on the way home. Notice how I am staying within the speed limit.
|
|
23 viewsProfessional photo taken at Burke Lake. Taken by Paul Baz.
|
|
For Sale 654 views
|
|
Me and Emily41 viewsMe and Emily at Rio Grande for Sandi's Birthday 2007
|
|
Mt. Vernon27 viewsContinuing to pass RA while we are in Mt. Vernon.
|
|
39 views
|
|
| Last additions |
Step 1: Locate the box containing the computer with the K40 Relay192 viewsThe K40 relay is located in the box indicated by my finger. It's right next to the battery. DO NOT OPEN IT YET, proceed to Step 2.Mar 08, 2010
|
|
Step 2: Remove the negative terminal connection on the battery214 viewsThis is probably the most important step. Remove the negative terminal connection on the battery as shown in the lower left hand corner of the photo. If you don't do this, you are probably going to short something out.Mar 08, 2010
|
|
Step 3: Remove the lid to the box containing the K40 relay242 viewsThere are 4 screws holding the lid on. Loosen these screws. The lid pops right off.Mar 08, 2010
|
|
Step4: Locate the computer containing the K40 relay257 viewsOnce you have taken the lid off, look for the bright orange 40 amp fuse. The module it is plugged into is the computer we need to pull out. To the right of the module is a brass clip holding the module in place. Pull back the clip and proceed to gently pull up and out the computer module.Mar 08, 2010
|
|
Step 5: Remove the 5 electrical plugs connected to the computer module263 viewsYou will notice there are 3 black connectors, and 2 gray connectors. Remove each connection gently. They may be on there tight, but all you have to do is pull them straight up. Don't worry, each connection is unique so you don't need to keep track of which connection goes where, it's pretty self explanatory.Mar 08, 2010
|
|
Step 6: Remove the computer from his housing275 viewsOnce you have the computer module out of the car, you need to bring it inside where you will remove the outer housing to expose the circuit board. Take a small flat head screw driver and gently separate the container from the circuit board. Mar 08, 2010
|
|
Step 7: Pull the circuit board from it's housing267 viewsOnce you have separated the circuit board from the housing, gently pull it up and out. I recommend pulling out the 40 amp fuse at this point too. You may want to clean up the contacts of the fuse, I found mine to be slightly dirty. Take a screw driver or wire brush and lightly scrap away any dirt or corrosion to make the fuse conntacts shiny. Now look in the upper left hand corner of of the circuit board and follow step 8.Mar 08, 2010
|
|
Step 8: Locate the damaged solder causing the K40 relay problem300 viewsIn the upper left hand corner of the circuit board you will see three solder points right next to each other. Any one of these may be bad. You need to remove the bad solder of any damaged connection, and re-solder. In the photo you will see that my K40 connection was damaged only on the right most of the 3 connections. The photo isn't great, but there was virtually no solder on this connection, and it looked dirty and almost as if it was slightly burned. The other 2 connections looked clean.Mar 08, 2010
|
|
